← All guides

Two RV appliances stopped at once

When a furnace and an air conditioner die together, or a fridge and a furnace both go quiet overnight, the instinct is that two things broke. They usually did not. RV appliances share control paths. Finding the shared part is faster than testing two appliances, and it stops you replacing the wrong one.

By OriginRV. Last reviewed on Nov 14, 2026.

The short version: ask what the two failed appliances have in common before testing either. On a coach with a Comfort Control Center thermostat, the furnace is not wired to the thermostat at all. It is wired to the roof air conditioner's control box, so when that box loses communication the whole system shuts down and the furnace goes with it. On a propane fault, every appliance runs off one regulator, and their demands differ by a factor of thirty. One shared part, two dead appliances.

The question to ask first

Two appliances failing together means they share a fault, and the way to find it is to work out what that is. There are only a few candidates, and they differ by which appliances are involved:

  • A control path. Some appliances are not controlled directly by the thermostat, and one of them is the furnace.
  • The 12 volt supply. Most appliance control boards run on 12 volts, so a shared circuit takes them down together.
  • The propane system. Every gas appliance draws from one regulator and one set of lines.
  • The transfer switch or the AC feed, if what died was 120 volt appliances.

Why the furnace dies when the air conditioner does

Dometic, describing how a Comfort Control Center system is wired: "If system includes a gas furnace, route two 18 gauge thermostat wires from the furnace to the roof opening of the unit that will control it."

On a Comfort Control Center system the furnace is not wired to the thermostat. It is wired to the roof air conditioner, and the thermostat talks to the air conditioner. On a coach whose furnace has its own wall thermostat, none of this applies and a dead furnace is a separate fault. The same instructions describe where those wires land: "Connect the previously run furnace thermostat wires (if applicable) to the blue wires to the 1/4" connectors at the electronic control box."

So the air conditioner's control box is the furnace's only route to a command. When that board drops off the network the thermostat reports it as "E1 Loss of communication between the CCC 2 thermostat and an individual system power module board", and displays the zone number that lost communication. The other E1, the one for losing contact with every board at once, takes the whole system down.

Which produces exactly the symptom people describe: the air conditioner stops, and so does the furnace, and the thermostat may be showing a code or nothing useful at all. Nothing is wrong with the furnace. It has lost the board that tells it what to do.

Two consequences follow. A furnace fault can be an air conditioner fault, so an E1 or a missing zone on the display puts the roof unit and its communication cable in scope before the furnace. And the cable itself is a suspect: Dometic specifies the thermostat communication cable as a four-conductor cable terminated with connectors at both ends, running between the thermostat and the roof unit, and the furnace wires join at the roof end. A loose or corroded connector in that chain takes out both appliances while both appliances are healthy.

Why the second appliance is often the fridge

The other pairing that comes up constantly is a furnace and a refrigerator failing together, and there is a separate reason for that one: they usually share a 12 volt control circuit rather than a control board.

A gas absorption refrigerator and a furnace both need 12 volts for their control boards even when they are running on propane. Their burners are gas, but their decisions are electric. So a fault in the shared 12 volt feed takes both down while the propane supply is untouched.

Which is why the useful test is the one that separates supply from appliance: check something else that runs on 12 volts. If the lights and the water pump are also weak or dead, the problem is upstream of every appliance and you are looking at a battery, a converter, a fuse or a ground. If everything else works normally, the shared circuit is narrower than the whole system, and you are looking for a fuse or a connection on one branch.

One pattern points the wrong way: a partially discharged battery can run one appliance but not two at once. A refrigerator and a furnace both trying to start will pull the voltage down far enough that neither succeeds, which looks like two failures and is really one supply that cannot carry the load.

Why the furnace and the water heater fail together

This pairing is usually propane rather than electric, and the makers' numbers explain why these two are the ones that complain. The demand table reproduced from NFPA 54 in the regulator handbook gives a warm air furnace at 100,000 BTU/hr, a range at 65,000, and a refrigerator at 3,000. That table is a generic sizing table for gas piping rather than a list of RV appliance ratings, and the furnace figure in it is a house furnace: the nameplate on your own furnace is the number to use.

A furnace is the largest gas consumer in the coach. Even at the small end of the RV range it asks for several times what a refrigerator does, which is why a system that is marginal rather than dead tends to show up here first. A water heater is the other appliance that calls for a large intermittent load, and it draws on the same regulator and the same lines, which is why the two show up together. Suburban names the mechanism from the appliance side, listing conditions that affect furnace performance including "low gas pressure caused by a number of factors, including a malfunctioning regulator or low gas levels in the tank."

The test is in the propane system rather than the appliances, and the makers publish it: system operating pressure of 11 inches of water column within half an inch, measured at 50 percent load, with lockout not exceeding 14 inches, and a drop-pressure test that bleeds to 8 inches of water column and must hold for three minutes. If a furnace and a water heater both fail while the stove lights, that test is the next step, not a furnace part. The propane guide carries the full procedure and the pressures to expect.

Can injure you That pressure test is a technician's, run on a live LP system with a manometer. A manometer on a charged system and a loosened gas fitting are not owner work. What an owner can do without argument is the soapy-water leak check on a connection and the visual inspection of the vent and the burner. If you smell gas, turn it off at the source, extinguish any flame, ventilate, and call a qualified service person.

If what died was 120 volt

A different shared part applies when the casualties are 120-volt: a microwave, an air conditioner, and the outlets. Those share the transfer switch and the breakers rather than a control board.

Can injure you This test is a live 120-volt reading at the switch box. The transfer switch is fed by shore power, the generator, or the inverter, depending on how the coach is set up: one of them is live while you meter. If you open the panel, unplug from shore power and switch the generator and inverter off first, and whatever you read live, the probes stay on the terminals and touch nothing else. If a live meter reading is not a job you are sure of, stop here and hand the meter to a technician.

The test there is a voltage reading on both sides of the switch. Progressive Dynamics gives the figure for their own unit in their troubleshooting instructions: "the readings should be equal", and between 105 and 130 VAC, on the generator input and on the output, with the note that if they are not similar the contactor is defective rather than the generator. Two 120 volt appliances failing together while the 12 volt lights are fine points at that switch, not at either appliance.

Working out which shared system it is

What failedLikely shared partWhat to check
Air conditioner and furnaceThe roof unit's control board and the communication cable, because the furnace is wired to itThe thermostat display for a communication fault, then the cable connectors at both ends
Furnace and refrigerator, both gas but both deadThe shared 12 volt control circuitWhether other 12 volt items work, then the fuse for that branch
Furnace and water heater, both on gasThe propane system, a regulator that is marginal rather than failedPressure at 50 percent load, and the drop-pressure test
Refrigerator and furnace, intermittently, more often when coldBattery voltage under loadVoltage at the appliances while both try to run, not at rest
Two 120 volt appliances, 12 volt side fineThe transfer switch or a shared breakerVoltage on both sides of the switch, expecting 105 to 130 on each

What this changes about the repair

The reason this matters is cost. A furnace that will not light is an appliance, and replacing an appliance is an expensive way to fix a cable connector. A refrigerator that will not cool is a cooling unit, and that is expensive too. When the two fail together, the shared part is almost always cheaper than either appliance.

What this costs

A cable connector, a fuse, a regulator, or a relay is a small part. A furnace, a refrigerator or an air conditioner is not, and the whole purpose of asking what the appliances share is to spend the small number first.

The order to work in: identify the pair, look up what they share, and test that one thing. On a control-path fault, that means the cable and connectors before the roof unit. On a 12 volt fault, that means the branch fuse and the voltage under load before any appliance. On a gas fault, that means the pressure test before the furnace. And on a 120 volt fault, a reading on both sides of the transfer switch before anything else. If the pair is a furnace and anything else, and the furnace has been short cycling, stop and read the carbon monoxide guide first, because that combination is documented as a route to carbon monoxide rather than to a repair.

Related guides

Two appliances out at once is usually the converter, and converter not charging works through it. If a fuse blows again as soon as you replace it, you have a short rather than a supply fault, and that is fuse keeps blowing. To check whether the two appliances together exceed what the circuit can carry, the watts to amps calculator converts their labels into amps.

Sources

Something wrong here, or something missing? Tell us.