RV delamination: What causes it, and what the makers actually document
A bubble in an RV sidewall is the outer skin coming away from whatever is glued behind it. The usual explanation is water, and water is one cause. It is not the only one, and that matters, because the assumption shapes both the diagnosis and the repair.
By OriginRV. Last reviewed on Nov 14, 2026.
What it actually is
Azdel makes the composite substrate that some RV walls use instead of plywood, and their definition is as direct as you will find: "Google defines Delamination as 'a structural failure where a material fractures, splits, or peels into separate layers. It is commonly caused by weak adhesion, mechanical stress, or environmental exposure'. We concur." They then say what it looks like in practice, in a sentence that names both layers: "Each image below shows a clear example of delamination. The exterior FRP layer has separated from the wood (lauan) layer behind it."
So the bubble is not a paint fault or a gelcoat fault. It is the outer skin no longer attached to the panel behind it.
Azdel goes further and names which bond matters: "The most critical adhesive bond in laminated walls is the outermost glue line between the exterior fiberglass and its substrate. Also known as the 'Gold Bond', the strength and longevity of this all-important bond is largely what will determine whether or not you experience delamination."
Water is not the only cause, and the substrate maker says so
"Some believe that water intrusion is required for delamination to take place. While this is indeed one cause, delamination can occur due to a number of reasons: poor glue coverage or workmanship; subpar quality in adhesive or substrate; frequent and/or extreme temperature fluctuations; and harsh weather conditions. Any one or a combination of these can initiate and accelerate delamination."
The temperature mechanism is documented separately, and it is a materials problem rather than a water problem: "As the temperature increased, FRP expanded but lauan contracted. As the temperature decreased, FRP contracted and lauan expanded... The result: no matter which direction the temperature fluctuates, lauan is continuously fighting with the FRP to move in the opposite direction, initiating and speeding up the delamination process."
That's a substrate supplier describing plywood as the wrong material for the job. It's a specific physical claim you can check against your own situation. A bubble on a wall you have never seen wet, on an RV kept in a hot climate, fits this explanation better than a leak does, though a bubble on its own cannot settle it: inspect and test the wall before deciding.
Where water is involved, Azdel describes the sequence on a plywood-backed wall: "Wood warping... Breakdown or rotting of the wood fibers... Breakdown and reduction in the adhesive bond between the wood layers themselves and the bond between the wood and the exterior FRP." The wood fails first, and the glue line follows it.
How the wall is built, from the makers who build them
Jayco describes their own laminated sidewall in five layers, and the order matters: "a layer of interior decorative plywood board is laminated... The exterior layer of the sidewall is formed utilizing a one-piece, glossy composite fiberglass panel... The final layer of the sidewall is a lauan plywood panel that is bonded between the fiberglass and the aluminum and foam wall assembly." On that build, the fiberglass is bonded to plywood, and the plywood is what the bubble separates from.
Jayco also makes a claim about its process that is worth quoting because it is the variable Azdel named first: "Jayco pinch rolling technique and the use of hot melt urethane allows Jayco to consistently provide 100% glue coverage."
Not every wall uses plywood, and a current maker's repair document says so plainly. Brinkley, in a sidewall replacement procedure: "The fiberglass is backed with an azdel material which may separate from the fiberglass and stick to the structure." And Keystone, in a sidewall crack repair bulletin, notes the layered version: "Please note the skin is backed with double layer of luan."
Grand Design's structural warranty treats the assembly itself as structural, which is the clearest statement of how serious this is: their defined "'Structural Components' consist of materials and/or workmanship directly attributable to Warrantor, namely, the laminated fiberglass sidewall assembly."
Checking it, and the mistake the instrument makers warn about
Before concluding water, measure. Protimeter documents the method: "pin-type meter measurements should be used to confirm the readings found by a pinless meter and are the predominant confirmation of excessive moisture." Scan first to find the area, then confirm with pins.
Protimeter's readings are set against a wood scale rather than the true moisture of a laminate, and the unit is WME, wood moisture equivalent: "a representative measurement of moisture content in a material as if it were wood", which is the right frame for a slide or sidewall floor because the material behind the skin is wood-based.
And the warning that will save you a false diagnosis: "Metal is a moisture meter's worst enemy. Conductive... contact with metal makes for moisture meter false readings. Areas that are actually dry will seem incredibly moist." RV walls contain aluminum framing and, on a slide-out, steel gear racks. Reading wet beside a metal member may be the meter reading the metal.
On a fiberglass or composite laminate specifically, the marine-style meters use a comparative index rather than a percentage. Tramex describes theirs as taking readings on "the comparative scale (0 to 100)", penetrating up to about 30 mm, and they are explicit about the limits: "Persistently high moisture readings may indicate an osmotic condition, but any diagnosis must include a thorough visual examination", and the instrument "will not detect or measure moisture through any electrically conductive materials or coatings."
The figures above are from instrument makers rather than from an RV standard, so treat them as the best available rather than as a rating.
The seals that lead to it, and the interval the makers specify
Where water is the cause, the entry points are documented and they are specific. On a slide-out they are documented separately, in the slide-out leaking guide, where the maker names the window seal rather than the roof. Winnebago publishes a sealant callout sheet naming the locations by part: "Side marker light Sealant A... Roof to Sidewall transition on Roofcap Sealant A... Roof to Rear Trim Joint Sealant B... TV Antenna Sealant B and C... Radio Antenna Sealant B... Edge Molding Sealant A." Airstream names their own list: "external seams and joints, such as end-shell segments and around window frames, light bezels, beltline and rub rail molding."
The maintenance interval is where the makers are stricter than most owners expect. Grand Design's structural warranty requires it as a condition of any claim: "Maintain all exterior seals and sealant, which must be inspected every 3 months to assure there are no gaps or voids and maintained annually." They add that if you seek a repair related to seals or sealant, "you must provide documentation acceptable to Warrantor that confirms completion of sealant inspections and maintenance for coverage consideration." Keystone gives the same cadence for the roof: "any attachments, seams, or joints in the roof material require maintenance every 90 days."
Ninety days is short. It is also the interval the makers put in writing, and two of them tie warranty coverage to whether you did it.
When a window seal is the one that has failed, RV window leaking covers where the water gets in, which sealant belongs on which seal, and how the window is held into the wall.
What the makers document about repair
What is documented is re-skinning, not injection. Brinkley's sidewall replacement procedure and Keystone's sidewall crack repair bulletin both describe removing and replacing the skin, and Keystone's bulletin includes the structural check that should come first, because a wall can crack for reasons that have nothing to do with water: "Inspect frame welds at sidewall securement plate(s). Take photos. Repair if necessary", and repair cracked joints with aluminum gussets.
That is worth holding onto. A crack or a bubble can be the visible symptom of a broken weld or a structural overload behind the skin, and Grand Design has run a customer satisfaction campaign for exactly that on a limited number of fifth wheels: "concerns of excessive frame flex or wall securement in the front upper deck area... due to a combination of manufacturing variations, an overload condition, or hitch modifications."
Opening a wet wall safely
OSHA, on porous materials: "As a general rule, if a porous material has been wet for over 48 hours it is best to remove and replace." That is a general rule about porous material rather than an RV repair standard: whether a wet wall section has to come out depends on the material and on how much of it is affected.
On protection, OSHA's cleanup guidance names the conditions that call for an approved respirator, at minimum a half or full-face N, R or P-100, along with non-vented goggles, long gloves and protective clothing: "areas greater than 100 ft.2, areas where mold is heavy... or areas where substantial dust is generated". That is a list of conditions to judge your own job against rather than a threshold that switches one rule on for everybody. The EPA uses the same 100 square feet as its own category boundary, the point where it recommends full containment.
The EPA also gives the clock, and it is shorter than most people assume: dry wetted materials or remove them within 24 to 48 hours.
What this costs
What the makers state is the shape of the decision: the bonded sidewall is a structural component in Grand Design's warranty language, and the documented repair is replacement of the skin rather than a patch. Brinkley's sidewall replacement work instructions and Keystone's sidewall crack repair bulletin are both that procedure, published by the makers themselves.
That sets the order to work in. Seal maintenance costs a tube of sealant and an afternoon every ninety days, and two makers make it a condition of coverage. A moisture meter costs little and tells you whether the wall is actually wet. Only then is there a repair decision, and it is a large one. The step that is cheap, repeatable and documented is the one worth doing first, and the interval is not annual.
Related guides
Delamination starts as a leak, and roof leak repair covers the usual entry points. A slide-out is the other place water gets in, and that is slide-out leaking. The maker's roof and sidewall documents are under exterior and body manuals.
Sources
- Azdel Onboard, What is Delamination?, for the definition of delamination, the statement that water is one cause among several including glue coverage and temperature, and the water-intrusion sequence on a plywood-backed wall.
- Azdel Onboard, RV and trailer sidewall exterior, for the Gold Bond as the critical outermost glue line, the construction stack, and typical substrate thicknesses.
- Azdel Onboard, water and moisture resistance, for the description of lauan as a moisture-vulnerable substrate.
- Azdel Onboard, temperature and humidity resistance, for the thermal expansion mismatch between fiberglass and lauan.
- Jayco, aluminum-framed vacuum bond lamination, for the five-layer sidewall build and the 100 percent glue coverage claim.
- Brinkley RV sidewall replacement procedure WI-029-2025, for the statement that the fiberglass is backed with Azdel which may separate, and for the documented repair being a skin replacement.
- Keystone RV sidewall crack repair bulletin KSB-210122, for the double layer of luan behind the skin and the requirement to inspect and repair frame welds first.
- Grand Design customer satisfaction campaign, November 2025, for the frame flex and wall securement condition caused by manufacturing variation, overload or hitch modification.
- Grand Design three year limited towable structural warranty, for the laminated fiberglass sidewall assembly being a structural component, and the three-monthly seal inspection required for coverage.
- Keystone RV, roof assembly maintenance, for the 90 day sealant maintenance interval.
- Winnebago sealants callout sheet, for the named sealant locations including marker lights, roof to sidewall transition, antennas and edge molding.
- Airstream, what to do if your Airstream has an exterior leak, for the named sealant inspection points including window frames, light bezels, beltline and rub rail.
- Protimeter, how does a moisture meter work, for the pinless scan then pin confirm method, the wood moisture equivalent explanation, and the warning that metal causes false readings.
- Tramex Skipper 5 moisture meter user guide, for the comparative 0 to 100 scale on composite laminates, the depth of signal penetration, and the limits including the inability to read through conductive materials.
- OSHA, mold hazards during disaster cleanup, for the guidance that porous material wet for over 48 hours is best removed and replaced, and the respirator and protective clothing requirements above 100 square feet.
- US EPA, mold remediation, for the 100 square foot containment threshold.
Something wrong here, or something missing? Tell us.
